T. Ching, J.Z.W. Lee, S.K.H. Win, L.S.T. Win, D. Sufiyan, C.P.X. Lim, N. Nagaraju, Y.-C. Toh, S. Foong, M. Hashimoto
Science Robotics, 9(2024) eadk4533 [Paper Link]
The idea came from playing with a carpenter's tape measure. A tape is stiff when you extend it, yet it can bend and roll back into a compact form. I noticed that its transverse curvature adds stiffness, and that this stiffness is anisotropic: the tape is much stiffer in one direction than the other. A flat film bends easily, a curved film resists bending, and it resists even more when the load pushes into the curve.
Building on this, I designed FiBa (film-balloon) actuators, which combine curved plastic films with small 3D-printed silicone balloons. They come in two types. In the bending actuator, a balloon sits between two curved films. When the balloon inflates, the film bends at a notch, and when it deflates, the stored stiffness springs the film back to its original shape. In the variable stiffness beam, a balloon runs along the inside of the film. When deflated, the beam can be folded and rolled up. When inflated, it pushes the film into a curve and becomes stiff. Each actuator weighs under 10 g.
The first robot was inspired by how a turtle crawls on land, using its flippers to push itself forward. I built the body from thin PVC sheets, cut on a plotter and snap-fitted together, with four FiBa bending actuators as flippers and two lifting actuators underneath. In each step, the flippers bend to push the robot forward. The lifting actuators then raise the body briefly so the flippers can reset without dragging it backward, and a vacuum pump pulls the body back down. The robot carries two micropumps, two valves, a battery, a microcontroller, and an IR receiver for remote control. The electronics weigh 40 g, and the whole robot weighs 70 g.
The second robot climbs a vertical pole the way an inchworm moves: grip, reach, grip again. It has two grippers connected by two FiBa bending actuators. Each gripper is a loop of PVC film lined with three balloons, which inflate to hug the pole. To climb, the top gripper holds on while the bending actuators pull the bottom gripper up. Then the bottom gripper holds on, the top one lets go, and the actuators straighten to push the top gripper higher. The robot itself weighs only 14 g, while the pumps, valves, battery, and controller add 54 g.
The third robot was inspired by how bats rest by hanging from branches. Most drones can only fly for under an hour, so being able to perch and turn off the motors could greatly extend their time in the field. The problem is that typical soft grippers are too heavy for a small drone; a commercial four-finger gripper weighs over 270 g. Using eight FiBa bending actuators, I built a four-finger gripper that weighs 55 g including its pump, valve, battery, and controller. It can lift a 322 g cup of coffee, about five times its own weight. I mounted it on top of a DJI Mavic Mini, which let the drone hang upside down from a tree branch with its motors off. On a small 260 mAh battery, the gripper held a 250 g load for over 3 hours.
The last robot was inspired by the ladybug, which tucks its wings into a compact shape and unfolds them when it wants to fly. Like the tape measure, a ladybug's wing gets its stiffness from a curved cross-section. I built a soft wing from thin PET film with two FiBa variable stiffness beams sewn inside. When deflated, the wing can be rolled and folded down to 14 cm. When inflated, it unfolds on its own to 37.5 cm and becomes stiff enough to carry a motor and propeller at its tip. Working with Shaohui Foong's group, we used this wing on a monocopter, a single-wing aircraft that spins like a maple seed as it flies. The monocopter unfolded its wing and went straight into flight. Their earlier version used a semi-rigid wing that had to be unfolded by hand. This one is fully soft, so it can be crushed flat and still deploy itself.